5

I have a virtual appliance running Ubuntu 14 that I would like to connect to a remote network via Meraki Client VPN.

I have found instructions for installing and configuring strongswan and xl2tpd on Ubuntu 16 which get me most of the way there, but after establishing the VPN I cannot seem to establish a route.

The goal is allow traffic from this single Ubuntu VM to a subnet on the remote LAN via the VPN.

(Ubuntu 192.168.5.99/32) =VPN> (Meraki appliance 20.20.20.20) => (Subnet 192.168.1.0/24)

https://gist.github.com/psanford/42c550a1a6ad3cb70b13e4aaa94ddb1c http://www.jasonernst.com/2016/06/21/l2tp-ipsec-vpn-on-ubuntu-16-04/

/etc/ipsec.conf:

# ipsec.conf - strongSwan IPsec configuration file

# basic configuration

config setup
        # strictcrlpolicy=yes
        # uniqueids = no

# Add connections here.

# Sample VPN connections

conn %default
        ikelifetime=60m
        keylife=20m
        rekeymargin=3m
        keyingtries=1
        keyexchange=ikev1
        authby=secret
        ike=aes128-sha1-modp1024,3des-sha1-modp1024!
        esp=aes128-sha1-modp1024,3des-sha1-modp1024!

conn meraki-vpn
     keyexchange=ikev1
     left=%defaultroute
     auto=add
     authby=secret
     type=transport
     leftprotoport=17/1701
     rightprotoport=17/1701
     # set this to the ip address of your meraki vpn
     right=20.20.20.20

/etc/xl2tpd/xl2tpd.conf :

[lac meraki]
lns = 20.20.20.20
ppp debug = yes
pppoptfile = /etc/ppp/options.l2tpd.client
length bit = yes

I can bring up the VPN:

root@zzz:~# ipsec up meraki-vpn
...
connection 'meraki-vpn' established successfully

Login:

echo "c meraki [email protected] mypassword" > /var/run/xl2tpd/l2tp-control

But I cannot get a route setup. Attempting to follow the magic recipes result errors. I can't figure if this is some xl2tpd config problem, or if I just can't figure the correct syntax to add the route. Any insight would be appreciated.

root@zzz:~# ip route add 192.168.1.0/24 dev ppp0
Cannot find device "ppp0"

ipsec statusall :

Status of IKE charon daemon (strongSwan 5.1.2, Linux 4.2.0-42-generic, x86_64):
  uptime: 20 hours, since Oct 19 19:30:38 2016
  malloc: sbrk 2433024, mmap 0, used 352240, free 2080784
  worker threads: 11 of 16 idle, 5/0/0/0 working, job queue: 0/0/0/0, scheduled: 4
  loaded plugins: charon test-vectors aes rc2 sha1 sha2 md4 md5 rdrand random nonce x509 revocation constraints pkcs1 pkcs7 pkcs8 pkcs12 pem openssl xcbc cmac hmac ctr ccm gcm attr kernel-netlink resolve socket-default stroke updown eap-identity addrblock
Listening IP addresses:
  192.168.5.99
Connections:
  meraki-vpn:  %any...20.20.20.20  IKEv1
  meraki-vpn:   local:  [192.168.5.99] uses pre-shared key authentication
  meraki-vpn:   remote: [20.20.20.20] uses pre-shared key authentication
  meraki-vpn:   child:  dynamic[udp/l2f] === dynamic[udp/l2f] TRANSPORT
Security Associations (1 up, 0 connecting):
  meraki-vpn[4]: ESTABLISHED 8 minutes ago, 192.168.5.99[192.168.5.99]...20.20.20.20[20.20.20.20]
  meraki-vpn[4]: IKEv1 SPIs: 2121ded4dc4dc94e_i* 3d5d1cc8bf935f19_r, pre-shared key reauthentication in 48 minutes
  meraki-vpn[4]: IKE proposal: 3DES_CBC/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024
  meraki-vpn{5}:  INSTALLED, TRANSPORT, ESP in UDP SPIs: c330d0b3_i 06749ffa_o
  meraki-vpn{5}:  3DES_CBC/HMAC_SHA1_96, 0 bytes_i, 0 bytes_o, rekeying in 8 minutes
  meraki-vpn{5}:   192.168.5.99/32[udp/l2f] === 20.20.20.20/32[udp/l2f]

ifconfig :

eth0      Link encap:Ethernet  HWaddr 00:0c:29:5f:9c:73  
          inet addr:192.168.5.99  Bcast:192.168.5.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fe5f:9c73/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:459939 errors:0 dropped:0 overruns:0 frame:0
          TX packets:362145 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:78969068 (78.9 MB)  TX bytes:52179997 (52.1 MB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:427152 errors:0 dropped:0 overruns:0 frame:0
          TX packets:427152 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:25278435 (25.2 MB)  TX bytes:25278435 (25.2 MB)

Thanks!

Improve this question
2
  • Guess I'm just SOL here. Why doesn't the ppp0 interface appear? Should this be created automatically by OpenSwan or xl2tpd, or is this some other mechanism? I am without a compass... anyone got a direction?
    – user3794652
    Commented Oct 25, 2016 at 16:52
  • the layer cake of client vpn is: <ipsec transport, l2tp, ppp>, so you need to be spawning a ppp process. PPP is also where the user/pass authentication is done, so I'm not sure how writing the credentials to l2tp is supposed to work (I've never used xl2tpd, though)
    – jdizzle
    Commented Jan 2, 2017 at 5:54

1 Answer 1

Reset to default
1

You need to disable xl2tpd sometimes as it runs and hogs port 1701 while the VPN client will normally start a service on 1701 only as needed.

I discovered this while I followed this answer quoted below and the blog post mentioned in it to get a connection working to Meraki from Ubuntu 16.04.

A PPA exists for network-manager-l2tp:

You can use

sudo add-apt-repository ppa:nm-l2tp/network-manager-l2tp  
sudo apt-get update  
sudo apt-get install network-manager-l2tp

To install the network manager l2tp that supports L2TP for Ubuntu 16.04

Walkthrough for building from source: http://blog.z-proj.com/enabling-l2tp-over-ipsec-on-ubuntu-16-04/

Improve this answer

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .